Antminer S17, S17pro vnish firmware

How to install

ATTENTION : BEFORE INSTALLING THE ANTMINER S17 / S17PRO FIRMWARE YOU MUST UNLOCK SSH (use file unlock ssh) !!!

Unlock SSH is working will all types of the Bitmain firmware except December 2019.

If you have Bitmain firmware December 2019 or above you must use SD CARD (you can find it on our web page). You can check the firmware version in the System – file system version.

Please contact us if you would like to participate in testing the version with the new GUI and functionality

download UNLOCK SSH UNLOCK SSH
download VNISH S17/S17pro SD IMAGE DOWNLOAD VNISH S17/S17pro SD IMAGE
DOWNLOAD FIRMWARE MANUAL DOWNLOAD FIRMWARE MANUAL
DOWNLOAD FIRMWARE FOR S17 / S17PRO VERSION 2.0.4 DOWNLOAD FIRMWARE FOR S17 / S17PRO (VERSION 2.0.4)

Modes antminer S17 firmware

POPULAR MODES VNISH FIRMWARE S17/S17pro:
53 TH/s – 2000 watt (37 watt-TH/s) 
57 TH/s – 2100 watt (37 watt-TH/s) 
60 TH/s – 2400 watt (40 watt-TH/s) 
70 TH/s – 2900 watt (41 watt-TH/s)
75 TH/s – 3300 watt (44 watt-TH/s)
80 TH/s – 3600 watt (45 watt-TH/s)

STOCK BITMAIN FIRMWARE S17/S17pro:
50 TH/s – 2320 watt (47 watt -TH/s)

Version changes in the antminer s17 vnish firmware release

Release 2.0.4 

1) Add option to disable temp sensors check 

Release 2.0.3 

1) General stability, optimization and revision of the main drivers.
2) Fixed incorrectly working profiles for the t17 model.
3) Fixed the translation for the correct display of the Russian language.
4) Fixed a web server error when the miner could freeze during a long uptime.
5) Added sleep mode option.
6) Added hotel fee option (where you can redirect part of the hashrate to pay for electricity, equipment colocation or pay for miners maintenance).
7) Added recalculation of the minimum hash rate if one or more boards have not been initialized.
8) Changed the operating mode of coolers when they are converted to 100% for 5 degrees from the critical temperature (it was 10).
9) Added a signature for complete security of virus protection with full ability to roll back to the stock firmware without an SD card, while leaving access to ssh for full access to your hardware and complete decentralization (SSH is disabled by default).
10) For those who unfortunately suffered from antbuild, we made a block so that your hash is not taken away.
11) Added a unique PROTECTION !!! On the hardware level against Antbuild and all similar viruses forever!!  

Release 2.0.1 

1) Modified, improved and accelerated the work of autotune.
2) Added an option that ignores the minimal voltage set in profile.
3) Corrected the mixed-up data entry in the auto-switch section.
4) renamed “fan rpm check” to “immersion mode” and moved to the settings section.  

Release 2.0.0

 1. General stability, refinement and refactoring of the main driver.
2. Improved display of chip hashrate.
3. Fixed the output display of the current timezone in the regional settings.
4. Made minor changes to the design of the web gui.
5. New profiles added:
S17 – 55th, 60th, 63th.
S17+ – 55th, 60th, 62th, 68th, 74th, 80th, 88th.
T17 – 40th.
T17+ – 40th, 48th, 55th, 63th, 68th.
6. Added an automatic correction of red domains (TIMER).
7. Extended voltage search ranges for auto-tuner profiles.
8. Added full customization of the miner’s manual auto-tuning.
9. Made a smooth change in the fan speed during miner initialization (without a sharp jump).
10. Added protection for breaking the chip chain to prevent equipment failure.
11. Added automatic “emergency” cooling mode, in case of “loss” of the miner temp sensors.
12. Added processing of erroneous data from temperature sensors.
13. Modified Log, now the status of the miner has become more understandable and detailed.
14. Implemented saving all miner logs even in the event of a complete reboot.
15. And most importantly, your miner will forget about overheating, bringing you a profit with maximum uptime due to the automatic switching of auto tuner profiles with a flexible system of settings to adapt the miner to changes in ambient temperature. Switching profiles is carried out by setting the temperature range and fan speeds for (automatic mode).  

Release 1.1.0

  1. General stability, code refactoring to simplify adding support for other models and finalizing the main driver
  2. Full support for ANTMINER S17 / S17PRO
  3. Full support for T17+
  4. Added a new way of reading temperature sensors (rewritten from scratch)
  5. Automatic switching to a lower profile when the miner overheats
  6. Automatically switches to a lowered profile when it is not possible to tune the selected profile
  7. Added a trigger for the maximum number of miner restarts in case of a board failure
  8. Improved cooler speed control algorithm (smooth transition from manual to automatic mode without failures)
  9. Fixed error setting voltage in manual mode
  10. Fixed the minimum hashrate check (worked when the value was 0 as disabled in the config)
  11. Added information on all successfully profiles tuned
  12. Added protection of the miner against hashrate theft by viruses
  13. Low temperatures mode is activated only when the silent mode is on (silent start)
  14. A trigger has been added that makes it possible to disable the function of heating (pre-heating) chips
  15. Fix a bug, when the firmware sets the cooler speed to 100% in manual mode

Release  1.0.0  

1. General stability.
2. Correction of profile parameters for ANTMINER S17 / S17PRO.
3. Improved nicehash support (extranonce subscribe).
4. Added trigger to disable / enable voltage (cold start).
5. Added trigger to disable / enable domain unbalance check.
6. Added the ability of target chip temp (new proprietary and much cooler adjustment method, which significantly reduced fan speed).
7. Implemented support for a “quiet” start of the miner.
8. Automatic transfer of the miner to warm-up mode when starting in cold conditions.
9. Added registration of dead chips during autotune.
10. Improved and significantly reduced the launch time of the miner.
11. Added saving chips freq / autotune result for subsequent manual pre-tuning.
12. Added checking for all types of viruses that we know about today.
13. All functionality is added to the config multiplier section.
14. Activated time zone.
15. Added the estimated power consumption by the miner (electronic wattmeter).
16. The status of the miner (its API) is available immediately at startup after 15 seconds.
17. Added The ability to set the critical temperature of the chips to automatically disable the hash board.    

Release  0.9.9 beta 1

  1. the autotune work has been finalized and fully adjusted
  2. completely rewritten algorithm for adjusting the voltage of the chips
  3. improved method for controlling unbalanced domains
  4. adjusted and fully customized profiles
  5. added compatibility with BTC Tools version 1.2.6
  6. fixed config multiplier with batch propagating workers
  7. added pool support for nicehash.com
  8. added pool support for warphash.com
  9. checked and fixed stability of the emcd.io pool
  10. checked and fixed stability of the Nicehash.com pool
  11. checked and fixed stability of the Bitcoin.com pool
  12. checked and fixed stability of the Ukrpool pool
  13. checked and fixed stability of the Warphash.com pool

Release  0.9.8  

1. General stability
2. Extended and refactored the main driver.
3. The next iteration of refinement and improvement of errors (HW)
4. Hash rate loss on some pools was analyzed and fixed.
5. Added support for P2P pool.
6. Activated the multiplier for the distribution of mass batch configs.
7. Work on with the reading of temperature sensors I2C
8. Created more than 10 overclocking profiles.
9. Added autotune!!! (note, autotune results are saved in a separate config, when changing a profile to a new one and returning to the previous profile, a repeated autotune is not required, except for a forced retune by the user).
After the completion of the tune, “temporarily” changes to the chips in the manual section of gui are not displayed.
10. Autotune is taken out as a separate log in the profiles section.
11. Automatic reboot when unbalancing domains to save chips from burnout.
12. Added manual downgrade of the entire domain.  

In release 0.9.6

  1. uptime stability
  2. main driver optimization
  3. compatibility with btc tools version 1.2.3.4
  4. added manual chip control function
  5. work was done on HW
  6. hashboard shutdown if the voltage is incorrect

Release 0.9.4

  1. general stability
  2. refactoring the driver code
  3. smoothing Hashrate display in miner status
  4. refinement of the automatic fan mode
  5. added led support:
    A) When minining led is blinking green
    B) When there are errors the led is solid red

Release 0.9.3

  1. overall stability
  2. driver refinement
  3. added option to select individually frequencies for each chain
  4. activated the config multiplier
  5. activated batch password change